Worx WG320 Manuel du propriétaire télécharger pdf (Page 16)

Cordless Limbing and Trimming Chain Saw EN

1716

1716

H). The cutting direction is inward on the

lower cutting edge.

9. With the mounting plate (a) side of the

Guide Bar facing the Motor (8) and holding

the Saw Chain in place on the bar, feed bar

and chain into the jaw, angling over the

bar locating pins (d) and pulling the Saw

Chain over the drive Sprocket (17) (See

Fig. I). There will be little excess Saw Chain

length, therefore, the Saw Chain must

be properly ﬁtted in the Guide Bar slot to

provide enough extra chain to be pulled

over the drive Sprocket.

10. Check if all parts are seated properly. (See

Fig J)

11. Reﬁt and tighten the Chain Tensioning Bolt.

Note the cam (e) of the Chain Tensioning

Bolt will engage the projecting tab (f) of

the bar mounting plate and push the bar

outward to tension the chain, check for

correct tension (See Adjusting the chain

tension).

12. Close the Chain Access Cover and remove

the Lock Pin.

LUBRICATION

IMPORTANT: The JAWSAW

®

is

shipped with an empty oil tank. It

is essential to ﬁll with chain oil before

use. Bar and chain oil of any brand can

be used.

Never operate the JAWSAW

®

without

chain oil or an empty tank as this will

result in poor cutting performance,

motor overload and possible burn-out.

FILLING OIL TANK:

1. Fill Oil Bottle (19) with chain and bar oil.

(See Fig. K)

2. Rest the JAWSAW

®

with the Oil Filler facing

upward.

3. Uncrew the oil ﬁller cap (g) open.

4. Use bottle to ﬁll oil reservoir. (See Fig. L)

5. Screw the oil ﬁller cap.

IMPORTANT: Use only the

recommended oil to avoid damage

to the JAWSAW

®

. Never use recycled/

old oil. Use of non approved oil will

invalidate the warranty.

CHECKING THE AUTOMATIC OILER

The JAWSAW

®

uses a much lower chain speed

than a conventional chainsaw so it needs

much less oil.

However it is very important that it always has

oil.

Check the Oil Level Window (14) and reﬁll as

necessary.

During operation, periodically check the

Saw Chain (8) and Guide Bar (7). A slight oil

presence should be visible. If the chain and

bar appear completely dry, then remove the

bar and chain (see previous section) to ensure

the bar oil hole is not blocked.

If the oil hole is clear, there is oil in the tank

and still no oiling of the chain is visible –

contact WORX customer service.

WARNING: Do not push the rear

handle repeatedly when the saw is

not cutting. The oil will be bumped out

when pushing the handle whether the

motor runs or not.

OPERATION

1. BEFORE USING YOUR CORDLESS

JAWSAW

®

Your battery pack is UNCHARGED and you

must charge once before use

The battery charger supplied is matched to the

Li-ion battery installed in the machine. Do not

use another battery charger.

2. CHARGING YOUR BATTERY PACK

The Li-ion battery is protected against deep

discharging. When the battery is empty,

the machine is switched off by means of a

protective circuit.

In a warm environment or after heavy use, the

battery pack may become too hot to permit

charging. Allow time for the battery to cool

down before recharging.

3. TO REMOVE OR INSTALL BATTERY

PACK (See Fig.M)

Depress the battery release button to release

battery pack from your JAWSAW

®

. After

recharging, insert the battery pack into

the battery port. A simple push and slight

pressure will be sufﬁcient.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 57 58

Commentaires sur ces manuels

Pas de commentaire